THE
MINISTRY OF INFORMATION AND COMMUNICATIONS
--------
|
THE
SOCIALIST REPUBLIC OF VIETNAM
Independence - Freedom - Happiness
---------------
|
No.
10/2019/TT-BTTTT
|
Hanoi,
October 04, 2019
|
CIRCULAR
PROMULGATION OF “NATIONAL TECHNICAL REGULATION ON ELECTROMAGNETIC
COMPATIBILITY FOR MOBILE TERMINALS AND ANCILLARY EQUIPMENT OF DIGITAL CELLULAR
TELECOMMUNICATION SYSTEMS”
Pursuant to the Law on Standards
and Technical Regulations dated June 29, 2006;
Pursuant to the Law on
Telecommunications dated November 23, 2009;
Pursuant to the Law on Frequencies
dated November 23, 2009;
Pursuant to the Government's Decree
No. 127/2007/ND-CP dated August 01, 2007 on elaboration of the Law on Standards
and Technical Regulations;
Pursuant to the Government's Decree
No. 78/2018/ND-CP dated May 16, 2018 on amendments to the Government's Decree
No. 127/2007/ND-CP dated August 01, 2007 on elaboration of the Law on Standards
and Technical Regulations;
Pursuant to the Government's Decree
No. 17/2017/ND-CP dated February 17, 2017 defining the functions, tasks, powers
and organizational structure of the Ministry of Information and Communications;
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
The Minister of Information and
Communications hereby promulgates a Circular on National technical regulation
on electromagnetic compatibility for mobile terminals and ancillary equipment
of digital cellular telecommunication systems.
Article 2.
Effect
1. This Circular comes into
force from July 01, 2020.
2. The Circular No. 02/2015/TT-BTTTT
dated February 27, 2015 of the Minister of Information and Communications shall
cease to have effect from July 01, 2020.
Article 3. Chief of Office, Director General of the Department of Science and
Technology, heads of agencies and units affiliated to the Ministry of
Information and Communications, Directors of Departments of Information and
Communications of provinces and central-affiliated cities and relevant
organizations and individuals are responsible for the implementation of this
Circular./.
THE
MINISTER
Nguyen Manh Hung
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
QUY CHUẨN KỸ THUẬT QUỐC GIA
VỀ TƯƠNG THÍCH ĐIỆN TỪ CHO THIẾT BỊ ĐẦU CUỐI VÀ PHỤ TRỢ TRONG HỆ
THỐNG THÔNG TIN DI ĐỘNG
National technical regulation
on electromagnetic compatibility for mobile terminals and
ancillary equipment of digital cellular telecommunication systems
Contents
1. GENERAL
1.1. Scope
1.2. Regulated entities
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
1.4. Definitions
1.5. Symbols
1.6. Abbreviations
2. TECHNICAL REQUIREMENTS
2.1. Emission
2.1.1. GSM and DCS
2.1.2. CDMA Direct Spread (UTRA and
E-UTRA)
2.2. Immunity
2.2.1. GSM and DCS
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
2.3. Test conditions
2.3.1. General
2.3.2. Arrangements for test
signals
2.3.3. Exclusion bands
2.3.4. Narrow band responses of
receivers and receivers of duplex transceivers
2.3.5. Normal test modulation
2.4. Performance assessment
2.4.1. General
2.4.2. Equipment which can provide
a continuous communications link
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
2.4.4. Ancillary equipment
2.4.5. Equipment classification
2.5. Performance criteria
2.5.1. GSM and DCS Performance
Criteria
2.5.2. CDMA Direct Spread (UTRA and
E-UTRA) Performance Criteria
3. MANAGEMENT REGULATIONS
4. RESPONSIBILITIES OF
ORGANIZATIONS AND INDIVIDUALS
5. IMPLEMENTATION
Annex A (normative) CDMA Direct
Spread Performance assessment voice call. Audio breakthrough
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Annex C (informative) Examples of cellular
mobile terminals and ancillary equipment
Bibliography
Foreword
QCVN 86:2019/BTTTT replaces QCVN
86:2015/BTTTT.
QCVN 86:2019/BTTTT contains
technical requirements that conform to ETSI EN 301 489-52 V1.1.0 (2016-11) of
the European Telecommunications Standards Institute (ETSI).
QCVN 86:2019/BTTTT is prepared by
the Research Institute of Posts and Telecommunications, appraised and submitted
by the Department of Science and Technology for approval, and promulgated
together with the Circular No. 10/2019/TT-BTTTT dated October 04, 2019 by the
Ministry of Information and Communications.
NATIONAL TECHNICAL REGULATION
ON ELECTROMAGNETIC COMPATIBILITY FOR MOBILE TERMINALS AND
ANCILLARY EQUIPMENT OF DIGITAL CELLULAR TELECOMMUNICATION SYSTEMS
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
- GSM, DCS
(IMT-2000, Technology GSM/EDGE) (see Annex C);
- UTRA,
WCDMA (IMT-2000 Direct Spread, W-CDMA FDD);
- E-UTRA,
LTE (IMT-2000 and IMT advanced) (see Annex C).
and
associated ancillary equipment.
Technical specifications related to
the antenna port and emissions from the enclosure port of radio equipment are
not included in the present document. Such technical specifications are found
in the relevant product standards for the effective use of the radio spectrum.
The present document only covers
public terrestrial mobile terminals on the List of potentially unsafe
commodities under management of the Ministry of Information and Communications.
The present document applies to
Vietnamese and foreign organizations and individuals involved in manufacturing
and sale of equipment in the scope of this document within the territory of
Vietnam.
QCVN 18:2014/BTTTT “National
technical regulation on General Electromagnetic Compatibility for Radio
Communications Equipment”
ETSI TS 134 108 (V6.4.0) (10-2006):
Universal Mobile Telecommunications System (UMTS); Common test environments for
User Equipment (UE); Conformance testing (3GPP TS 34.108 version 6.4.0 Release
6).
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
ETSI TS 134 109 (V6.2.0) (09-2006):
Universal Mobile Telecommunications System (UMTS); Terminal logical test
interface; Special conformance testing functions (3GPP TS 34.109 version 6.2.0
Release 6)
ETSI EN 300 296-1 (V1.4.1) (2013):
Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile
Service; Radio equipment using integral antennas intended primarily for
analogue speech; Part 1: Technical characteristics and methods of measurement.
Recommendation ITU-T P.64 (1999):
Telephone transmission quality, Telephone installations, Local line networks,
Objective electro-acoustical measurements. Determination of
sensitivity/frequency characteristics of local telephone systems.
Recommendation ITU-T P.76 (1988): Telephone
transmission quality, Measurements related to speech loudness, Determination of
loudness ratings; Fundamental principles, Annex A.
ETSI TS 125 102 (V7.4.0) (10-2006):
Universal Mobile Telecommunications System (UMTS); User Equipment (UE) radio
transmission and reception (TDD) (3GPP TS 25.102 version 7.4.0 Release 7).
ETSI TS 136 101 (V8.4.0) (01-2009):
LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); User Equipment (UE)
radio transmission and reception (3GPP TS 36.101 version 8.4.0 Release 8).
ETSI TS 136 508 (V8.1.0) (04-2009):
LTE; Evolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Packet
Core (EPC); Common test environments for User Equipment (UE) conformance
testing (3GPP TS 36.508 version 8.1.0 Release 8).
ETSI TS 136 509 (V8.0.1) (01-2009):
LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Special conformance
testing function for User Equipment (UE) (3GPP TS 36.509 version 8.0.1 Release
8).
ETSI I-ETS 300 034-1 (Edition 1)
(10-1993): European digital cellular telecommunications system (Phase 1); Radio
subsystem link control (GSM 05.08).
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
ETSI ETS 300 578 (Edition 13)
(03-1999): Digital cellular telecommunications system (Phase 2) (GSM); Radio
subsystem link control (GSM 05.08 V4.22.0).
ETSI TS 100 911 (V8.23.0)
(11-2005): Digital cellular telecommunications system (Phase 2+); Radio
subsystem link control (3GPP TS 05.08 version 8.23.0 Release 1999).
information transmission path of
defined characteristics for transfer of user data or predefined test data.
UE is in idle mode and has
completed the cell selection/reselection process and has chosen a cell.
NOTE 1: The UE monitors system
information and (in most cases) paging information.
NOTE 2: The services may be
limited, and the PLMN may not be aware of the existence of the UE within the
chosen cell.
RF bandwidth supporting a single
E-UTRA RF carrier with the transmission bandwidth configured in the uplink or
downlink of a cell.
NOTE: The channel bandwidth is
measured in MHz and is used as a reference for transmitter and receiver RF
requirements.
ancillary which provides send
and/or receive data access to UMTS services via UE.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
For UTRA/EUTRA equipment: state of
User Equipment (UE) when switched on but with no Radio Resource Control (RRC)
connection.
For GSM: mode of operation of a
receiver or a transceiver, where the Equipment Under Test (EUT) is powered,
available for service and available to respond to a request to set up a call.
average transmitter output power
obtained over any specified time interval, including periods with no
transmission, when the transmit time slots are at the maximum power setting.
maximum achievable throughput for a
reference measurement channel.
for a given class of emission, the
width of the frequency band which is just sufficient to ensure the transmission
of information at the rate and with the quality required under specified
conditions.
measure of the received signal
quality, which is generated by the mobile or portable equipment, for use as a
criterion in the Radio Frequency (RF) power control and handover processes
NOTE: For more information see:
- ETSI ETS
300 034-1 clause 8.2 for Phase 1 GSM 900 equipment;
- ETSI ETS
300 034-2 clause 8.2 for Phase 1 DCS 1800 equipment; or
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
- ETSI TS
100 911 clause 8.2 for Phase 2+ GSM 900 or Phase 2+ DCS 1800 equipment.
state of User Equipment (UE) when
switched on and with Radio Resource Control (RRC) connection established.
number of payload bits successfully
received per second for a reference measurement channel in a specified
reference condition.
entity capable of accessing a set
of cellular services via one or more radio interfaces.
NOTE: This entity may be stationary
or in motion within the cellular service area while accessing the Cellular
services, and may simultaneously serve one or more users.
BWChannel Channel
Bandwith
m meters
AC
Alternating Current
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
ARFCN
Absolute Radio Frequency Channel
Number
BCCH
Broadcast Control Channel
BER
Bit Error Ratio
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Block Error Ratio
BPF
Band Pass Filter
BTS
Base Transceiver Station
CCCH
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
CDMA
Code Division Multiple Access
CW
Continuous Wave (unmodulated
carrier wave)
DC
Direct Current
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
DCS
Digital Cellular
telecommunications System
DL
Down Link (From BTS to UE)
DTX
Discontinuous Transmission
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
E-UTRA
Absolute Radio Frequency Channel Number
EMC
Electromagnetic Compatibility
EPC
Evolved Packet Core
ESD
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
EUT
Equipment Under Test (UE or UE
with ancillaries)
E-UTRA
Evolved Universal Terrestrial
Radio Access
FDD
Frequency Division Duplex
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
FRC
Fixed Reference Channel
GSM
Global System for Mobile
Communications
PCCPCH
Primary Common Control Physical
Channel
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Radio Frequency
rms
root mean square
RRC
Radio Resource Control
SPL
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
TCH
Traffic channel
TDD
Time Division Duplex
UARFCN
UTRA Absolute Radio Frequency
Channel Number
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
UE
User Equipment
UL
Up Link (From UE to BTS)
UMTS
Universal Mobile
Telecommunication System
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Universal Terrestrial Radio
Access
EMC
emission measurements for ports of radio and/or associated ancillary equipment
are provided in Table 1 in QCVN 18:2014/BTTTT (see Table 1) and conditions are set
out in Table 2 of the present document.
Table 1. EMC
emission measurements for mobile terminals and ancillary equipment of GSM and
DCS under Table 1, QCVN 18:2014/BTTTT
Phenomenon
Application
Equipment test requirement
Reference clause in QCVN
18:2014/BTTTT
Radio and ancillary equipment
for fixed use (e.g. base station equipment)
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Radiated emission
enclosure of ancillary equipment
applicable for stand alone
testing
applicable for stand alone
testing
2.1.3
Conducted emission
DC power input/output port
Applicable
Not applicable
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Conducted emission
AC power input/output port
Not applicable
Not applicable
2.1.5
harmonic current emissions
AC mains input port
Not applicable
Not applicable
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Voltage fluctuations and flicker
AC mains input port
Not applicable
Not applicable
2.1.7
Conducted emission
Telecommunication port
Not applicable
Not applicable
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Table 2.
Conditions for EMC emission measurements for mobile terminals and ancillary
equipment of GSM and DCS
Reference clause in QCVN
18:2014/BTTTT
Conditions for measurements,
additional to or modifying Clause 2.1 in QCVN 18:2014/BTTTT
2.1.3 “Enclosure of ancillary equipment measured on a stand
alone basis”
At the manufacturer's discretion, ancillary equipment can also
be measured in combination with the radio equipment under test. When the
ancillary equipment is measured in combination with the radio equipment,
radiated emissions from the transmitter/transceiver shall be ignored, but
recorded in the test report.
EMC emission measurements for ports
of radio and/or associated ancillary equipment are provided in Table 1 in QCVN
18:2014/BTTTT (see Table 1).
EMC immunity measurements for ports
of radio and/or associated ancillary equipment are provided in Table 2 in QCVN
18:2014/BTTTT (see Table 3) and conditions are set out in Table 4 of the
present document.
Table 3. MC
emission measurements for mobile terminals and ancillary equipment of GSM and
DCS under Table 2, QCVN 18:2014/BTTTT
Phenomenon
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Equipment test requirement
Reference clause in QCVN
18:2014/BTTTT
Radio and ancillary equipment
for fixed use (e.g. base station equipment)
Radio and ancillary equipment
for vehicular use (e.g. mobile equipment)
RF electromagnetic field (80 MHz
to 1 000 MHz and 1 400 MHz to 2 700 MHz)
enclosure
Applicable
Applicable
2.2.3
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
enclosure
Not applicable
Applicable
2.2.4
Fast transients, common mode
signal, telecommunication and
control ports, DC and AC power ports
Not applicable
Not applicable
2.2.5
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
signal, telecommunication and
control ports, DC and AC power ports
Applicable
Not applicable
2.2.6
transients and surges
DC power input ports
Applicable
Not applicable
2.2.7
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
AC mains input port
Not applicable
Not applicable
2.2.8
surges, line to line and line to
ground
AC mains power input ports,
telecommunication ports
Not applicable
Not applicable
2.2.9
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Reference clause in QCVN
18:2014/BTTTT
Conditions for measurements,
additional to or modifying Clause 2.2 in QCVN 18:2014/BTTTT
2.2.3 “Radio frequency electromagnetic field”, “Test method”
clause
When using the max hold detector method at each test frequency
step initially an unmodulated test signal shall be applied. Then the test
modulation shall be applied.
The test shall be repeated with the equipment in the idle mode
of operation and the exclusion band shall not be used during this test.
2.2.6 “Radio frequency, common mode”, “Test method” clause
When using the max hold detector method at each test frequency
step initially an unmodulated test signal shall be applied. Then the test
modulation shall be applied.
The stepped frequency increments may be 50 kHz increment of the
momentary frequency in the frequency range 150 kHz to 5 MHz. When using the
max hold detector method, initially at each test frequency step an
unmodulated immunity test signal shall be applied. Then the modulation of the
immunity RF test signal (1 kHz tone) shall be applied as specified in QCVN
18:2014/BTTTT.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
During tests with pulses 3a and 3b, the performance criteria TT
shall apply (see clause 2.5.1.3).
EMC
immunity measurements for ports of radio and/or associated ancillary equipment
are provided in Table 2 in QCVN 18:2014/BTTTT (see Table 3) and conditions are
set out in Table 5 of the present document.
Table 5.
Conditions for immunity measurements for mobile terminals and ancillary
equipment of CDMA Direct
Spread (UTRA and E-UTRA)
Reference clause in QCVN
18:2014/BTTTT
Conditions for measurements,
additional to or modifying Clause 2.2 in QCVN 18:2014/BTTTT
2.2.3 “Radio frequency electromagnetic field”, “Test method”
clause
When using the max hold detector method at each test, frequency
step initially an unmodulated test signal shall be applied. Then the test
modulation shall be applied.
2.2.6 “Radio frequency, common mode”, “Test method” clause
There is no exclusion band for the equipment in the scope of the
present document.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
The procedure used for identifying narrowband responses does not
apply to conducted immunity tests in the frequency range 150 kHz to 80 MHz
(see clause 2.3.4).
2.2.7. “Transients and surges in the vehicular environment”,
“Performance criteria” section
During tests with pulses 3a and 3b, the performance criteria TT
shall apply (see clause 2.5.1.3).
The test conditions are set out in
Annex A in QCVN 18:2014/BTTTT and the provisions in clauses 2.3.2 to 2.3.5 of
the present document.
Whenever the EUT is provided with a
detachable antenna, the EUT shall be tested with the antenna fitted in a manner
typical of normal intended use, unless specified otherwise.
2.3.2.1.
Arrangements for test signals for GSM and DCS
The provisions of QCVN
18:2014/BTTTT, A.2 shall apply with the following modifications given in
clauses 2.3.2.1.1 to 2.3.2.1.3.
2.3.2.1.1.
GSM and DCS Arrangements for establishing a communications link
The nominal frequency of the wanted
RF input signal (for the receivers) shall be selected by setting the Absolute
Radio Frequency Channel Number (ARFCN) to an appropriate number (e.g. in case
of GSM 900 MHz this is 60 to 65, and in case of GSM 1 800 MHz this is 690 to
706).
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
When the EUT is required to be in
the transmit/receive mode, the following conditions shall be met:
- the EUT shall be commanded to operate at maximum transmit
power;
- the downlink RXQUAL shall be monitored.
2.3.2.1.2.
GSM and DCS Calibration of the overall audio link performance
Prior to the test sequence, the
reference level of the speech output signal on both the downlink and uplink
shall be recorded on the test instrumentation, as shown in figure 1.
If the equipment does not include
acoustical transducers (e.g. a microphone or loudspeaker) the equivalent
electrical reference levels shall be specified
by the manufacturer.
The voice processor may often apply
noise and echo cancellation algorithms which attempt to eliminate or reduce steady state audio signals as e.g. the 1 kHz calibration signals.
The calibration should be carried
out with the noise and echo cancellation algorithms disabled.
If the noise and echo cancellation
algorithms cannot be disabled then the reference level of the speech output
signal should be measured using a max-hold detection on the audio level meter
in order to determine the level before the noise and echo cancellation
algorithms become effective.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
- The EUT is not used for the calibration of the downlink. Adjust
the output of the audio test source to achieve a reference level equivalent to
a SPL of 0 dBPa at 1 kHz at the input of the acoustic coupler for the downlink.
Record the reading of the audio level meter as the reference level.
- If in handsfree applications an external loudspeaker is used,
the SPL from the external loudspeaker is higher
than
that from the earpiece of the portable by a certain amount in order to overcome
a high ambient noise level. Two methods can be used to achieve the required
SPL:
+ the
downlink reference level shall be increased by the same amount in order to
compensate for the difference
in SPL; or
+ the
distance between the loudspeaker and the measuring microphone shall be adjusted
during the measurement procedure.
Calibration of the uplink:
- For the calibration of the uplink the EUT is used. Adjust the
output of the audio test source to achieve a reference level equivalent to a
SPL of -5 dBPa at 1 kHz at the Mouth Reference Point (MRP) defined in
Recommendation ITU-T P.64. Record the reading of the audio level meter, which
is connected to the output of
the test system, as the reference level.
- For handsfree applications, normally no corrections are made to
the uplink reference level. If it is not possible to perform the above
calibration, the manufacturer shall
specify the distance between the
MRP and the microphone.
Figure 1.
Audio breakthrough measurement, calibration set-up for portable equipment
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
The voice processor may apply noise
and echo cancellation algorithms which attempt to eliminate or reduce steady
state audio signals as e.g. the 1 kHz calibration signals.
When the audio levels are measured
during testing the EUT software shall be configured for voice applications. If
the algorithms for noise and echo cancellation are not disabled, then the level
shall be measured using a max-hold detection on the audio level meter in order
to determine the level before the noise and echo cancellation algorithms become
effective.
Set the EUT volume to provide the
nominal audio level if specified by the manufacturer. If no such level is
specified, the centre volume step shall be
used. The volume settings shall be recorded in the test report.
The level of the output signal from
the downlink speech channel of the EUT at the mobile or portable's earpiece
shall be assessed by measuring the Sound Pressure Level (SPL) as shown in
figure 2. When an external loudspeaker is used the acoustic coupler shall be
fixed to the loudspeaker in the position used during the calibration.
The level of the decoded output
signal from the uplink speech channel of the EUT at the analogue output of the
test system shall be measured. Pick up of extraneous background noise by the
microphone of the EUT shall be minimized by sealing
the speech input port (microphone) of the EUT (see figure 2).
If the equipment is designed for
use with external transducers, they shall be included in the test
configuration. If the equipment does not include acoustical transducers the
line voltage developed across a specified termination impedance may be
measured.
Figure 2:
Audio breakthrough measurement, test set-up for portable equipment
2.3.2.2.
Arrangements for test signals for CDMA Direct Spread (UTRA and E-UTRA)
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
- The
wanted RF signal nominal frequency shall be selected by setting the UTRA or
E-UTRA Absolute Radio Frequency Channel Number (UARFCN or EARFCN) to an
appropriate number;
- A
communication link shall be set up with a suitable base station simulator
(hereafter called "the test system"). The test system shall be
located outside of the test environment;
- Where
possible the test of the transmitter section and receiver section of the EUT
may be carried out simultaneously to reduce test time.
Immunity tests shall be performed
in two modes of operation:
- with a
communication link established (traffic mode); and
- in the
idle mode.
When the EUT is required to be in
the traffic mode, a call is set up according to the Generic call set-up
procedure and the following conditions shall be met:
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
- the DTX
shall be disabled;
- Inner Loop
or Up Link Power Control shall be enabled;
- for UTRA
the transmitting and/or receiving (UL/DL) bit rate for reference test channel
shall be 12,2 kbit/s. E-UTRA the transmitting and/or receiving (UL/DL) bit rate
for reference test channel shall be the reference measurement channel as
specified in Annex C in ETSI TS 136 101 with parameters specified in tables
7.3.1-1 and 7.3.1-2 in ETSI TS 136 101;
- For UTRA
see ETSI TS 134 108 and ETSI TS 134 109 Logical Test Interface for details regarding
generic call set-up procedure and BER, BLER test loop scenarios; for E-UTRA see
ETSI TS 136 508 and ETSI TS 136 509 for details regarding generic call set-up
procedure and throughput test loop scenarios.
When the EUT is required to be in
the idle mode the following conditions shall be met:
- UE shall be
camped on a cell;
- UE shall
perform Location Registration (LR) before the test, but not during the test;
- UE's
neighbour cell list shall be empty;
- paging
repetition period and DRX cycle shall be set to minimum (shortest possible time
interval).
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
2.3.2.3. Arrangements
for test signals at the input of transmitters
The provisions of QCVN
18:2014/BTTTT, A.2.1 shall apply. For GSM and DCS, A.2.1 in
QCVN 18:2014/BTTTT shall apply with the following modifications:
- The test
system shall command the EUT to disable Discontinuous Transmission (DTX);
- A
communication link shall be set up between the EUT and the test system.
2.3.2.4. Arrangements
for test signals at the output of transmitters
The provisions of QCVN
18:2014/BTTTT, A.2.2 shall apply with the following modifications:
- Where the
equipment incorporates an external 50 Ω RF antenna connector that is
normally connected via a coaxial cable, then the wanted signal to establish a
communication link shall be delivered from that connector by a coaxial cable.
- Where the
equipment incorporates an external 50 Ω RF antenna connector, but
this port is not normally connected via a coaxial cable, and where the
equipment does not incorporate an external 50 Ω RF
connector (integral antenna equipment), then the wanted signal, to establish a
communication link, shall be delivered from the equipment to an antenna located
within the test environment.
2.3.2.5. Arrangements
for test signals at the input of receivers
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
The provisions of QCVN
18:2014/BTTTT, A.2.3 shall apply with the following modifications:
- Where
the equipment incorporates an external 50 Ω RF antenna connector that is
normally connected via a coaxial cable, then the wanted signal to establish a
communication link shall be delivered from that connector by a coaxial cable.
- Where
the equipment incorporates an external 50 Ω RF antenna connector, but this port
is not normally connected via a coaxial cable, and where the equipment does not
incorporate an external 50 Ω RF connector (integral antenna equipment), then
the wanted signal, to establish a communication link, shall be delivered from
the equipment to an antenna located within the test environment.
2.3.2.5.2. Arrangements
for test signals at the input of GSM and DCS receivers
The wanted RF input signal level
shall be set to 40 dB above the reference sensitivity level as defined in ETSI
TS 100 911, clause
6.2 to provide a stable communication link.
2.3.2.5.3. Arrangements
for test signals at the input of CDMA Direct Spread (UTRA and E-UTRA) receivers
For immunity testing the wanted RF
signal level at the input of the EUT shall be at least 40 dB above the
reference sensitivity level to provide a stable communication link. The
reference sensitivity level is defined in ETSI TS 125 101 and ETSI TS 125 102
or ETSI TS 136 101.
For emission testing the wanted RF
signal level at the input of the measuring receiver shall be no more than 15 dB
above the reference sensitivity level, to ensure that it operates within its
dynamic range.
2.3.2.6.
Arrangements for test signals at the output of receivers
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
The provisions of QCVN
18:2014/BTTTT, A.2.4 shall apply.
When the EUT is required to be in
the idle mode, the test system shall simulate a Base Station (BS) with
Broadcast Control Channel/Common Control Channel (BCCH/CCCH) on one carrier.
The EUT shall be synchronized to the BCCH, listening to the CCCH and able to
respond to paging messages. Periodic Location Updating shall be
disabled.
2.3.2.6.2.
Arrangements for test signals at the output of CDMA Direct Spread (UTRA and
E-UTRA) receivers
The provisions of QCVN
18:2014/BTTTT, A.2.4 shall apply. The specific arrangements for test
signals at the output of receivers are in annexes A and B.
2.3.3.1.
GSM and DCS Receiver and receivers of duplex transceivers exclusion band
The provisions of QCVN
18:2014/BTTTT, A.3 shall apply.
The exclusion band for receivers
and receiver sections of transceivers is the band of frequencies over which no
immunity tests with radiated RF are made.
2.3.3.2.
GSM and DCS Transmitter exclusion band
The provisions of QCVN
18:2014/BTTTT, A.3 shall apply.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
2.3.3.3. CDMA Direct
Spread (UTRA and E-UTRA) Transmitter exclusion band
The provisions of QCVN
18:2014/BTTTT, A.3 shall apply.
2.3.3.4. CDMA Direct
Spread (UTRA and E-UTRA) Receiver exclusion band
The provisions of QCVN
18:2014/BTTTT, A.3 shall apply.
2.3.4.1.
GSM and DCS Narrow band responses of receivers and receivers of duplex
transceivers
Responses on receivers or duplex
transceivers occurring during the test at discrete frequencies which are narrow
band responses (spurious responses), are identified by the following method
(the procedure below only applies if the separation between test frequencies
exceeds 500 kHz):
-
if during an immunity test the RXQUAL or speech output signal
level being monitored goes outside the specified figure, it is necessary to
establish whether the RXQUAL increase or speech output signal level increase is
due to a narrow band response or to a wide band phenomenon. Therefore,
the test shall be repeated with the unwanted signal frequency increased, and
then decreased by 400 kHz;
-
if the RXQUAL increase or speech output signal level increase
disappears in either or both of the above 400 kHz offset cases, then the
response is considered as a narrow band response;
-
if the RXQUAL increase or speech output signal level increase does
not disappear, this may be due to the fact that the offset has made the
frequency of the unwanted signal correspond to the frequency of another narrow
band response. Under these circumstances the procedure is repeated with the
increase and decrease of the frequency of the unwanted signal set to 500 kHz;
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Narrow band responses are
disregarded.
2.3.4.2.
CDMA Direct Spread (UTRA and E-UTRA) Narrow band responses on receivers
2.3.4.2.1.
UTRA
Responses on receivers or duplex
transceivers occurring during the immunity tests at discrete frequencies, which
are narrow band responses (spurious responses), are identified by the following
method:
- if during
an immunity test the quantity being monitored goes outside the specified
tolerances, it is necessary to establish whether the deviation is due to an
unwanted effect on the receiver of the UE or on the test system (narrow band
response) or to a wideband (EMC) phenomenon. Therefore, the test shall be
repeated with the UARFCN increased or decreased by:
+ FDD bands
I, VIII.
- if the
deviation does not disappear, the procedure is repeated with the UARFCN
increased or decreased from the original value by:
+ FDD bands
I, VIII.
- if the
deviation does not disappear with the increased and/or decreased UARFCN, the
phenomenon is considered wideband and therefore an EMC problem and the
equipment fails the test.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
2.3.4.2.2.
E-UTRA
Responses on receivers or duplex
transceivers occurring during the immunity tests at discrete frequencies, which
are narrow band responses (spurious responses), are identified by the following
method:
- if during
an immunity test the quantity being monitored goes outside the specified
tolerances, it is necessary to establish whether the deviation is due to an
unwanted effect on the receiver of the UE or on the test system (narrow band
response) or to a wide band (EMC) phenomenon. Therefore, the test shall be
repeated with the unwanted signal frequency increased or decreased by BWChannel
MHz, where BWChannel is the channel bandwidth as defined in ETSI TS 136 101;
- if the
deviation does not disappear, the procedure is repeated the unwanted signal
frequency increased or decreased by 2 × BWChannel MHz,
- if the
deviation does not disappear with the increased and/or decreased frequency, the
phenomenon is considered wide band and therefore an EMC problem and the
equipment fails the test.
Narrow band responses are
disregarded.
2.3.5.1. GSM and DCS
Normal test modulation
The immunity tests in voice call
mode shall be performed without the application of any external modulation
input signal.
For immunity tests in voice call
mode, the overall audio uplink and downlink performance of the radio equipment
shall be calibrated before the start of the tests. The
calibration procedure is explained in clause 2.3.2.1.2.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
2.3.5.2. CDMA Direct
Spread (UTRA and E-UTRA) Normal test modulation
For transmission of analogue speech
or audio signals (voice call mode), immunity tests shall be performed without
the application of any external modulation input signal.
The overall audio Up Link (UL) and
Down Link (DL) performance of the radio equipment shall be calibrated before
the start of the tests. The calibration procedure is explained in clause A.1..
The immunity tests in the data
transfer mode shall be performed with the application of an appropriate
external modulation input signal such that the performance of the data call can
be monitored. For assessment of the data transfer mode, refer to Annex B.
The provisions of QCVN
18:2014/BTTTT, B.1 shall apply with the following modifications:
- The
information about the bandwidth of the IF filter immediately preceding the
demodulator as set out in Annex B in QCVN 18:2014/BTTTT is not applicable
to radio equipment in the scope of the present document.
2.4.2.1. GSM and DCS
Equipment with analogue speech circuits
The provisions of QCVN
18:2014/BTTTT, B.2 shall apply.
The performance of equipment which
supports voice and data calls is assessed based on the voice call.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
The provisions of QCVN
18:2014/BTTTT, B.2 shall apply.
The assessment of the equipment
performance shall be specified by the manufacturer.
The provisions of QCVN
18:2014/BTTTT, B.3 shall apply.
2.4.4.1.
GSM and DCS Ancillary equipment
The provisions of QCVN
18:2014/BTTTT, B.4 shall apply with the following modifications:
- For
emission measurements on transmitters performed in conjunction with associated
ancillary equipment, the radiated emissions from the transmitter shall be
ignored.
2.4.4.2. CDMA
Direct Spread (UTRA and E-UTRA) Ancillary equipment
The provisions of QCVN
18:2014/BTTTT, B.4 shall apply with the following modifications:
- Ancillary
equipment shall be tested with it connected to a UE in which case compliance
shall be demonstrated to the appropriate clauses of the present document.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
- Portable or
mobile equipment or combinations of equipment, when used in conjunction with a
charger powered from the AC mains, shall in addition fulfil the requirements of
radio and ancillary equipment for fixed use.
The equipment shall meet the
performance criteria specified in this clause and clauses 2.5.1.2 to
2.5.1.4, as appropriate.
Portable equipment intended for use
whilst powered by the main battery of a vehicle shall additionally fulfil the
applicable requirements set out in QCVN 18:2014/BTTTT, clauses 2.1
and 2.2 for mobile equipment.
Portable or mobile equipment
powered by the AC mains shall additionally fulfil the applicable requirements
of QCVN 18:2014/BTTTT, clauses 2.1 and 2.2 for radio and
ancillary equipment for fixed use.
The establishment and maintenance
of a communications link, the assessment of RXQUAL, and the assessment of the
audio breakthrough by monitoring the speech output signal level, are used as
performance criteria to ensure that all primary functions of the transmitter
and receiver are evaluated during the immunity tests. In
addition, the test shall also be performed in idle mode to ensure the
transmitter does not unintentionally operate.
The maintenance of a communications
link shall be assessed using an indicator which may be part of the test system
or the EUT.
If an equipment is of a specialized
nature, such that the performance criteria described in the following clauses
are not appropriate, then the manufacturer shall declare, for inclusion in the
test report, his own specification for an acceptable level of performance or
degradation of performance during. The performance
specification shall be included in the product description and documentation.
The performance criteria specified
by the manufacturer shall give the same degree of immunity protection as called
for in the following clauses.
A communication link shall be
established at the start of the test, see clauses 2.3.2.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
NOTE: When there
is a high level background noise present the filter bandwidth can be reduced
down to a minimum of 40 Hz.
At the conclusion of the test, the
EUT shall operate as intended with no loss of user control functions or stored
data, and the communication link shall have been maintained. In addition
to confirming the above performance during a call, the test shall also be
performed in idle mode, and the transmitter shall not unintentionally operate.
A communication link shall be
established at the start of the test, see clause 2.3.2.
At the conclusion of each exposure
the EUT shall operate with no user noticeable loss of the communication link.
At the conclusion of the total test
comprising the series of individual exposures, the EUT shall operate as
intended with no loss of user control functions or stored data, as declared by
the manufacturer, and the communication link shall have been maintained.
In addition to confirming the above
performance during a call, the test shall also be performed in idle mode, and
the transmitter shall not unintentionally operate.
A communication link shall be
established at the start of the test, see clause 2.3.2.
During the test, the RXQUAL of the
downlink shall not exceed the value of three, measured during each individual
exposure in the test sequence.
During the test, the downlink
speech output level shall be at least 35 dB less than the previously recorded
reference levels, when measured through an audio band pass filter of width 200
Hz, centred on 1 kHz (audio breakthrough check).
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
At the conclusion of the test, the
EUT shall operate as intended with no loss of user control functions or stored
data, and the communication link shall have been maintained.
A communication link shall be
established at the start of the test, see clause 2.3.2.
At the conclusion of each exposure
the EUT shall operate with no user noticeable loss of the communication link.
At the conclusion of the total test
comprising the series of individual exposures, the EUT shall operate as
intended with no loss of user control functions or stored data, as declared by
the manufacturer, and the communication link shall have been maintained.
The provisions of QCVN
18:2014/BTTTT, C.4 shall apply.
2.5.2.1.
General
The equipment shall meet the
performance criteria specified in this clause and clauses 2.5.2.2 and
2.5.2.3 as appropriate.
The maintenance of a communications
link shall be assessed by using an indicator, which may be part of the test
system or the equipment under test.
If an equipment is of a specialized
nature, such that the performance criteria described in the following clauses
are not appropriate, then the manufacturer shall declare, for inclusion in the
test report, his own specification for an acceptable level of performance or
degradation of performance during. The performance specification shall be
included in the product description and documentation.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
In addition, the test shall also be
performed in idle mode to ensure the transmitter does not unintentionally
operate.
2.5.2.2. Performance
criteria for continuous phenomena
2.5.2.2.1.
General
A communication link shall be
established at the start of the test.
In the speech mode, the performance
criteria shall be that the Up Link and Down Link speech output levels shall be
at least 35 dB less than the recorded reference levels, when measured through
an audio band pass filter of width 200 Hz, centred on 1 kHz (Annex A).
NOTE: When there
is a high level of background audio noise present, the filter bandwidth can be
reduced down to a minimum of 40 Hz.
At the conclusion of the test, the
EUT shall operate as intended with no loss of user control functions or stored
data, and the communication link shall have been maintained.
In addition to confirming the above
performance during a call, the test shall also be performed in idle mode, and
the transmitter shall not unintentionally operate.
2.5.2.2.2.
UTRA
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
-
if the BER (as referred in ETSI TS 134 109) is used, it shall not
exceed 0,001 during the test sequence;
-
if the BER (as referred in ETSI TS 134 109) is used, it shall not exceed 0,01
during the test sequence.
The BLER calculation shall be based
on evaluating the CRC on each transport block.
2.5.2.2.3.
E-UTRA
In the data transfer mode, the
performance criteria shall be that the throughput shall be ≥ 95 % of
the maximum throughput of the reference measurement channel as specified in
Annex C in ETSI TS 136 101 with parameters specified in tables 7.3.1-1 and
7.3.1-2 in ETSI TS 136 101 during the test sequence.
2.5.2.3.
Performance criteria for Transient phenomena
A communications link shall be
established at the start of the test, clauses 2.3.1 and 2.3.2.
At the conclusion of each exposure
the EUT shall operate with no user noticeable loss of the communication link.
At the conclusion of the total test
comprising the series of individual exposures, the EUT shall operate as
intended with no loss of user control functions or stored data, as declared by
the manufacturer, and the communication link shall have been maintained.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
3.1.
Equipment in the scope of Clause 1.1 of the present document must comply with
technical requirements specified in the present document and have its
conformity declared under the present document.
3.2. For
GSM mobile terminals, the present document shall apply instead of QCVN
86:2015/BTTTT for the purpose of complying with regulations on conformity
declaration of the Ministry of Information and Communications.
3.3. For
W-CDMA FDD mobile terminals and E-UTRA FDD mobile terminals, the present
document shall apply instead of QCVN 18:2014/BTTTT for the purpose of complying
with regulations on conformity declaration of the Ministry of Information and
Communications.
Relevant
organizations and individuals shall comply with regulations on declaration of
conformity of equipment in the scope of the present document and be subject to
inspection by regulatory agencies in accordance with applicable regulations.
5.1.
Vietnam Telecommunications Authority, Authority for Radio Frequency Management
and Departments of Information and Communications shall provide guidelines for
management of radio equipment in accordance with this document.
5.2. In the cases where any of the
provisions referred to in this document is amended or replaced, the newest one
shall apply.
5.3. Difficulties that arise during the implementation of
this document should be reported to the Ministry of Information and
Communications (the Department of Science and Technology) for instructions and
resolution./.
A.1. Calibration of audio levels
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Set the EUT
volume to provide the nominal audio level if specified by the manufacturer. If no such
level is specified, the centre volume step shall be used.
Prior to
the test sequence, the reference level of the speech output signal on both the
downlink and uplink shall be recorded on the test instrumentation, as shown in
figure A.1. The reference level shall be equivalent to the SPL of 0 dBPa at 1
kHz at the input of the acoustical coupler described ETR 027 for the
downlink, and -5 dBPa at 1 kHz at the mouth reference point (MRP) defined in
Recommendation ITU-T P.64 for the uplink.
NOTE 1: The MRP is
defined with respect to an artificial head defined in Recommendation ITU-T
P.76. The handset should be mounted on the artificial head such that the ear
piece is centred at the artificial ear.
NOTE 2: If the
equipment does not include acoustical transducers (e.g. a microphone or
loudspeaker) the manufacturer should specify the equivalent electrical
reference levels.
The voice
processor may often apply noise and echo cancellation algorithms, which attempt
to eliminate or reduce steady state audio signals as e.g. the 1 kHz calibration
signals. These algorithms may be disabled during the calibration procedure. Specialized
test software may be required. If the algorithms cannot be
disabled then the reference level shall be measured using a max-hold detection
on the audio level meter in order to determine the level before the noise and
echo cancellation algorithms become effective.
Normally no
corrections are made to the uplink reference level. The manufacturer shall
specify the distance between the MRP and the microphone.
Figure A.1.
Audio
breakthrough measurement, calibration set-up for portable equipment
NOTE: The EUT is in position
during calibration of the uplink, but not during calibration of the downlink
where the EUT is replaced by the 1 kHz test audio source. During calibration of
the uplink the mouthpiece shall be placed with respect to the MRP in a way representing intended use.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
When the
audio levels are measured during testing the EUT software shall be configured
for voice applications. If the algorithms for noise and echo cancellation are not
disabled, then the level shall be measured using a max-hold detection on the
audio level meter in order to determine the level before the noise and echo
cancellation algorithms become effective.
The level
of the output signal from the downlink speech channel of the EUT at the mobile
or portable's ear piece shall be assessed by measuring the Sound Pressure Level
(SPL) as shown in figure A.2. When an external loudspeaker is used the
acoustical coupler shall be fixed to the loudspeaker in the position used
during the calibration. The level of the decoded output signal from the uplink speech
channel of the EUT at the analogue output of the test system shall be measured. Pick up of
extraneous background noise by the microphone of the EUT shall be minimized.
NOTE: If the
equipment is designed for use with external transducers, they should be
included in the test configuration. If the equipment does not
include acoustical transducers the line voltage developed across specified
termination impedance may be measured.
Figure A.2.
Audio breakthrough measurement, test set-up for portable equipment
CDMA
Direct Spread Performance assessment of data transfer call. Error Ratios
B.1.
Calibration of data transfer
B.1.1. UTRA
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
B.1.2. E-UTRA
For the EUT, calibration of the
data transfer may be performed by assessing the throughput percentage before
applying the RF immunity test signal.
B.2. Assessment
of data transfer
B.2.1. UTRA.
Derivation of Error Ratios
The manufacturer shall provide the
method for calculating the Error Ratio. Known data patterns shall be
transferred bi-directionally from end-to-end (the whole of the UL and DL will
be exercised). Performance assessment shall be made at each frequency step. Comparison
between transmitted known data and received data shall result in the Error
Ratio.
The data patterns used should be of
sufficient length to give valid results and should be equivalent to the used
channel bit rate.
Possible data patterns for
assessing the Error Ratio are BER, BLER and User Data. Detailed description of
BER and BLER can be found from ETSI TS 134 109.
End-User Data may be used where BER
and BLER measurements are not appropriate and is a manufacturer's decision.
EXAMPLE: In the
cases when the EUT consists of UE with data application ancillary and the data
application ancillary itself does not support a loopback function that can be
applied for the assessment of BER or BLER, as specified in ETSI TS 134 109. This would
lead into a situation where the data application ancillary is not exercised,
i.e. the data transfer loop is not end-to-end.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Following formula may apply to
End-User Data:
Error
Ratio
=
erroneuos(bits,
bytes,symbols,etc.)
x 100
=
n%
total
number of (bits, bytes,symbols,etc.)
(In case
that high Error Ratios exist, ensure that errors are a consequence of EMC
stress.)
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
The data
patterns used should be of sufficient length to give valid results and should
be equivalent to the used channel bit rate.
B.3. EUT without data application ancillary
Data
monitoring Devices are here considered as part of the Test System. Arrangements
should be made by the manufacturer, if needed, to couple the Data monitoring
Device by a method which does not affect the radiated electromagnetic field
(e.g. ultrasonic or optical).
Figure B.1.
Error Ratio or throughput assessment, test set-up for EUT without data
application ancillary
B.4. EUT with data application ancillary
The Data
monitoring Device is here considered as a part of the Test System. The Data
application ancillary should be part of the data transfer (UL and DL) loop and
is included in the EUT configuration.
Figure B.2.
Error Ratio or throughput assessment, test set-up for EUT with data application
ancillary
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
Annex C
(informative)
Examples
of cellular mobile terminals and ancillary equipment
C.1.
Phase 1, Phase 2, and Phase 2+ GSM 900 MHz and DCS 1800 MHz
digital cellular mobile terminals and ancillary equipment
Definitions for Phase 1, Phase 2,
and Phase 2+ GSM 900 MHz and DCS 1800 MHz digital cellular mobile terminals and
ancillary equipment are found
in:
- ETSI I-ETS
300 034-1 for Phase 1 GSM 900 equipment
- ETSI
I-ETS 300 034-2 for Phase 1 GSM 1800 equipment; or
- ETSI ETS
300 578 for Phase 2 GSM 900 or Phase 2 DCS 1800 equipment;
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66
C.2. Cellular mobile terminals and ancillary equipment for the
IMT-2000 CDMA Direct Spread (UTRA)
Definitions for cellular mobile
terminals and ancillary equipment for the IMT-2000 CDMA Direct Spread (UTRA)
are found in:
- ETSI TS
125 101 and ETSI TS 125 102.
C.3. Cellular mobile terminals and ancillary equipment for the
Evolved Universal Terrestrial Radio Access (E-UTRA)
Definitions for cellular mobile
terminals and ancillary equipment for the Evolved Universal Terrestrial Radio
Access (E-UTRA) are found in :
- ETSI TS
136 101.
Bibliography
[1] ETSI EN
301 489-52 V1.1.0 (2016-11) Electromagnetic Compatibility (EMC) standard for
radio equipment and services; Part 52: Specific conditions for Cellular
Communication Mobile and portable (UE) radio and ancillary equipment;
Harmonised Standard covering the essential requirements of article 3.1(b) of
Directive 2014/53/EU.
...
...
...
Bạn phải
đăng nhập hoặc
đăng ký Thành Viên
TVPL Pro để sử dụng được đầy đủ các tiện ích gia tăng liên quan đến nội dung TCVN.
Mọi chi tiết xin liên hệ:
ĐT: (028) 3930 3279 DĐ: 0906 22 99 66